-
First, sort your generator into one of these scenarios
-
Scenario A: Standby generators on natural gas or propane
-
Scenario B: Portable generators on gasoline
-
Scenario C: Small engines and the BPMR7A vs B6HS question
-
The glow plug vs spark plug mix-up
-
How to figure out which scenario you're actually in
I review accessory and replacement-part batches for an electrical equipment distributor—roughly 300 SKUs a month across generators, transfer switches, and the small stuff people actually break. Spark plugs generate more returns than almost anything else in that catalog (not because the plugs are bad, but because people buy the wrong one).
There's no single "best" plug for a Generac. The right answer depends on what the engine burns, how often it runs, and what the manual says for your serial number. So instead of a top-10 list, here's how I'd sort the problem.
First, sort your generator into one of these scenarios
Most people asking about spark plugs fall into one of three buckets, plus one group that shouldn't be looking at spark plugs at all:
- Standby generator on natural gas or propane (e.g., the Generac 7291 26kW class)
- Portable generator on gasoline (e.g., a Generac 6500W unit)
- Small engine equipment—trimmers, mowers, small pumps—where NGK BPMR7A and B6HS come up
- Diesel units—these use glow plugs, not spark plugs, and they're a different conversation
If you're not sure which bucket you're in, the fuel is the fastest tell. Gasoline, natural gas, or propane means spark ignition. Diesel means compression ignition.
Scenario A: Standby generators on natural gas or propane
Take the Generac 7291 26kW. Air-cooled, twin-cylinder, runs on natural gas or propane, and sits idle for weeks at a time before a transfer event. That duty cycle shapes the plug choice more than any spec sheet headline.
Because the unit runs infrequently and under fairly stable load, the factory-specified plug is usually the right plug. Generac's manual for a given serial range lists a model and a gap; both matter. I've seen people swap in an iridium plug "for reliability" and then wonder why the engine idles rough. Iridium resists erosion longer, which is great when you're racking up hours. On a standby unit that runs maybe 20 hours a year, that longevity advantage is basically theoretical—and you've paid three or four times as much for it.
My rule for standby: replace with the OEM-spec plug at the interval in the manual, check the gap out of the box (they get crushed in shipping), torque to spec rather than by feel, and don't get creative. Honestly, the boring answer is usually the efficient one. That's not a knock on premium plugs—it's that a five-minute gap check prevents more failures than an upgrade ever will.
It took me about four years of reviewing warranty claims to understand that most "failed" spark plugs weren't defective. They were the wrong plug, gapped wrong, or torqued by feel instead of with a wrench.
Scenario B: Portable generators on gasoline
A Generac 6500W portable is a different animal. Gasoline, intermittent use, often stored in a garage or shed between storms, and frequently fed E10. Ethanol blends attract moisture and leave deposits when they sit—so the plug sees more fouling than a standby unit ever will.
Two things matter here: gap and condition. The gap widens as the electrode wears, and a wide gap is harder to fire under load. That's the failure mode people miss—the generator starts fine with no load, then stumbles the moment the AC kicks on.
Here's a mistake I made myself, and it's common enough that I now mention it at the counter: skipping the annual gap check because "it ran fine last season." One cold snap, the unit cranked and cranked and wouldn't catch. Pulled the plug—gap was nearly double spec, electrode rounded off. Twenty minutes with a feeler gauge would have saved a service call and a very cold house.
Check the gap against your manual (it varies by model—don't guess), replace if the electrode is rounded or heavily fouled, and if you're storing it more than a month, run the carb dry and consider a fuel stabilizer. The plug is usually the messenger, not the root cause.
Scenario C: Small engines and the BPMR7A vs B6HS question
This is where most of the confusion lives. Both plugs share the same thread (M14 × 1.25) and reach (12.7mm), so they'll physically thread into the same hole. They are not interchangeable in practice.
- NGK BPMR7A—projected tip, resistor type, heat range 7. Common on small two-stroke equipment like trimmers and chainsaws, and on some small four-strokes.
- NGK B6HS—standard tip, non-resistor, heat range 6. A workhorse plug for small four-stroke engines.
The heat range number is where people go wrong. Per NGK's own heat range chart, a higher number doesn't mean "hotter" or "more powerful"—it means the plug sheds heat faster (a "colder" plug). Put a cold plug in a low-load engine and it fouls. Put a hot plug in a high-load engine and you risk pre-ignition and electrode damage.
People think a hotter plug makes more power. Actually, heat range is about matching the plug's heat dissipation to the engine's operating temperature. The engine design decides the range; you just don't want to fight it.
Also worth noting: the resistor (the "R" in BPMR7A) suppresses radio-frequency interference. On equipment with sensitive electronics—or anything near a radio—that matters. B6HS doesn't have it. That's not a defect; it's a different design intent.
The glow plug vs spark plug mix-up
Every so often someone asks whether they can run a glow plug in their gasoline generator, or why their diesel unit doesn't have a spark plug. These are different ignition systems, and they don't cross over.
A spark plug creates a high-voltage arc that ignites a fuel-air mixture. A glow plug is a heating element—it warms the combustion chamber so diesel will ignite under compression on a cold start. Once the engine is running, the glow plug's job is largely done. A diesel engine has no spark plug because it doesn't need a spark; compression does the igniting.
If you're searching "glow plug vs spark plug" because your unit won't start, check the fuel type first. Gasoline, natural gas, propane—spark plug. Diesel—glow plug, and a whole different troubleshooting tree.
How to figure out which scenario you're actually in
Skip the forum threads and do this in order:
- Fuel type. Gasoline, NG, or propane → spark plug. Diesel → glow plug.
- Owner's manual. Find the plug model and gap for your serial number. This beats any cross-reference chart, including the one at the parts counter.
- Duty cycle. Standby (long idle, stable load) → OEM spec, don't get creative. Portable (intermittent, E10) → check gap annually. Small equipment → match the plug to the engine type, not just the thread size.
- Condition. If the electrode is rounded or the insulator is cracked, replace—don't regap a worn plug and call it good.
Bottom line: the efficient move isn't finding the "best" plug. It's matching the plug to the engine and the way it's used, then checking the gap before you install it. That's a five-minute habit that prevents most of the no-start calls I see come through returns (note to self: print this for the counter staff).

