Before You Order That Switch, Check Six Things
If you're specifying an on off on momentary switch, a DPST on-off switch, or a metal push button switch for a production line, stop and verify six parameters first. Miss even one, and you're looking at a 2–4 week delay and roughly 30–40% of the order value in returns, rework, or emergency substitutions. I know this because I've paid for those misses three times — $4,700 total — over eight years handling electrical component orders.
The six parameters, in the order they cause the most damage:
- Operation type (momentary vs. maintained)
- Contact configuration (SPST / DPST / SPDT / DPDT)
- Switch function position sequence (on-off-on, on-on, etc.)
- Actuator and enclosure material
- Electrical ratings (voltage, current, AC vs. DC)
- Environment and mounting (IP rating, panel cutout, terminal type)
The one that bites most people — and bit me the hardest — is the interaction between #1 and #2. An operationally momentary switch can still have a DPST contact block. People assume "momentary" means "single circuit." It doesn't.
Why I Built This Checklist (The $4,700 Story)
I handle electrical component sourcing for an industrial integrator. I've been doing this since 2017, and I've placed somewhere north of 600 component orders in that time. Three of them went badly wrong in ways that were entirely avoidable.
The first was in my second year. I ordered 120 electrical push button switches for a control panel retrofit. The spec sheet said "momentary, DPST." I confirmed the momentary spec with the engineer and placed the order. What I didn't confirm was the function sequence. The panel design called for a three-position selector — off / jog / on — with the jog position momentary. I'd ordered a two-position on-off momentary. Eighty of those switches came back. Cost: $1,180 in restocking, plus a five-day production delay.
The second was worse. In September 2022, I ordered 40 metal push button switches for an outdoor conveyor control station. Stainless housing, IP67 rated, everything looked right. But I'd matched the panel cutout to our existing 22mm standard and didn't check the new vendor's actual bezel diameter. Their "22mm" was 22.3mm — within tolerance for their own panel, but not for ours. We ended up machining every opening wider on-site. That error cost $890 in rework plus a week of technician time.
The third one still irritates me. A customer asked for a dpdt momentary push button switch with a specific automotive-style sealed connector. I found one that matched the contact configuration, the momentary action, and the DPDT requirement. I skipped the temperature rating check because the application was "indoor." The enclosure was an unheated warehouse bay that hit 41°C in summer. The switches' rubber seals degraded within four months. Replaced all 60 units at our cost. That one ran about $2,630 including labor.
After that third one, I built the six-point list. We've used it on 47 switch orders since January 2024. It's caught issues on 11 of those orders before the PO went out — mostly wrong function sequence and AC/DC rating mismatches. Estimated savings so far: somewhere around $8,000 in avoided rework.
The Six Parameters, and Where Each One Bites
1. Momentary vs. Maintained — and Why It's Not as Obvious as It Sounds
A momentary switch returns to its rest position when you release it. A maintained switch stays where you put it. That part is simple. The confusion starts when you're dealing with a multi-position switch like an on off on momentary switch — where, say, the "off" position is maintained but the two "on" positions are momentary. Or vice versa. I've seen data sheets where the momentary behavior only applies to one position, and the others are maintained. Read the function table, not the headline description.
2. Contact Configuration — SPST, DPST, SPDT, DPDT
This is where I lost the most money. A DPST on-off switch has two poles, each with a simple on/off action. A DPDT switch has two poles, each with a changeover contact (normally open and normally closed). A dpst on off switch is not interchangeable with a DPDT switch, even if both are "two-pole." The wiring diagrams are completely different.
Here's the counterintuitive part: a switch can be momentarily operated and have a DPST or DPDT contact block. The "momentary" label describes the actuator behavior; the contact configuration describes the electrical path. These are independent specs. I conflated them once, and that's what caused the $1,180 mistake above.
3. Function Sequence — The Parameter Nobody Checks
On-off, on-off-on, on-on, off-on — the position sequence matters and it is almost never in the part number. You have to read the function table. If you're ordering an on-off-on switch, confirm which positions are momentary and which are maintained. I now highlight the function table on every data sheet and attach it to the PO. It's saved us at least four times.
4. Actuator and Enclosure Material
Metal push button switches are not all the same metal. Stainless steel, nickel-plated brass, and aluminum have very different corrosion behavior. For outdoor or washdown environments, stainless is usually the right call. For an automotive push button switch, you're often dealing with sealed connectors and specific mounting depths that vary by manufacturer. Check the panel cutout drawing, not just the nominal size.
5. Electrical Ratings — Especially AC vs. DC
A switch rated for 10A at 250VAC may only handle 2A at 30VDC. DC arcs don't self-extinguish the way AC arcs do at zero-crossing, so the DC rating is almost always lower. If you're switching a DC load — like a solenoid or a DC motor contactor — you need the DC rating, full stop. This is the single most common field failure I've seen on control panels. Per IEC 60947-5-1, the utilization category (AC-15, DC-13, etc.) tells you the intended load type. If your supplier's datasheet doesn't list a DC rating, assume it doesn't have one.
6. Environment and Mounting
IP rating, panel cutout diameter, terminal type (screw, push-in, solder), and operating temperature range. The temperature spec is the one I skipped in 2023 — see the $2,630 mistake above. For warehouse or outdoor installations, check the max operating temperature on the datasheet and compare it to the actual environment, not the "typical" one.
When This Checklist Doesn't Apply
I should be honest about the boundaries here. My experience is based on roughly 600 orders in industrial control and automation — panels, conveyors, machine tools. If you're specifying switches for consumer electronics, medical devices, or aerospace, the priorities are different. Medical devices will care about biocompatibility and sterilization cycles. Aerospace will have entirely separate qualification standards. My checklist is a floor, not a ceiling.
Also, this is for standard catalog switches. If you're having something custom-tooled, the vendor's engineering team will usually catch spec mismatches during the DFM review — though I've learned not to assume that, either.
One more thing: I've never fully understood why some vendors list a "momentary" function on a switch that clearly has a maintained detent in the same position range. My best guess is that the datasheet template is reused across product families, and the function descriptions don't always get updated. If anyone has insight into that, I'd genuinely like to hear it — because it's caused me to double-check every function table by hand for the past three years.
To be fair, most switch orders go fine. The six parameters above aren't complicated — they're just easy to skip when you're moving fast. And that's the whole point: five minutes of spec verification beats three weeks of replacement parts, emergency rework, and the awkward email to your customer explaining why their panel doesn't work.

